No products in the cart.
Product categories
Filter by Brand
Product tags
Price range
Filter by price
Price Range
$ -
Product tags
- This product cannot be added to the cart because the price is not set.
- Replacement Plugs
JL Audio – HD-PWRPLUG2-4AWG-RP Replacement Power Plug (Type 1)
Replacement small power input plug for select HD and MHD Amplifiers:
Fits the following models only:
HD600/4
HD900/5
HD750/1 (excluding HD750/1 with Serial Numbers > #108034000001, which use )
MHD600/4
MHD900/5
MHD750/1 (excluding MHD750/1 with Serial Numbers > #153034000001, which use )Corresponding plug shroud on applicable amplifiers has phillips head screws.
Need additional information on selecting the correct plug?
SKU: HD-PWRPLUG2-4AWG-RP - Remote Level Control
JL Audio – HD-RLC Amplifier Remote Level Control and Cable
Remote Level Control for Select JL Audio Amplifiers
The HD-RLC remotely controls the Bass Level of the following JL Audio amplifiers:
HD-Series: All models
XD-Series: All models
MHD-Series: All models
M-Series: All modelsWhen the HD-RLC is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle.
The HD-RLC kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. (5.5 m) cable.
A satin-finish aluminum knob can be purchased separately.
SKU: JL Audio - HD-RLC - Line Output Converter
JL Audio – LoC-22 Fully Active, Two-Channel Speaker Level to Line Output Converter with Auto Turn-On
Line Output ConverterJL Audio – LoC-22 Fully Active, Two-Channel Speaker Level to Line Output Converter with Auto Turn-On
Fully Active, Two-Channel Speaker Level to Line Output Converter with Auto Turn-On
Designed by JL Audio Sr. Engineer Bruce Macmillan, the LoC-22 is an active two-channel processor engineered for applications requiring the attenuation of factory audio signals for use with aftermarket amplifiers and signal processors.
The LoC-22 utilizes a fully regulated, switching MOSFET power supply and an all-analog circuit design to deliver flat frequency response, at any signal level (3 Hz – 32 kHz, +0, -1dB), without altering bass response at high levels, like many passive line output converters do.
Engineered to combat induced cable noise, the LoC-22 features a differential-balanced input architecture making it compatible with virtually any analog audio signal. Capable of accepting up to 40V RMS per channel (equivalent to 400W @ 4 ohms), the LoC-22 easily handles the most powerful factory amplifier outputs. An onboard dual-range input load switch allows compatibility with most factory amplifiers that employ impedance sensing to mute channels.
Ideal for full-range or low-frequency applications, the LoC-22 is equipped with a pair of analog RCA-type, line-level output jacks (up to 8V RMS) to feed audio signals to your aftermarket system. Analog outputs are compatible with most types of aftermarket signal processors or amplifiers. Setting output levels is super simple and easy, thanks to a specially calibrated, onboard clipping indicator that works with test tones or music. The LoC-22 offers two automatic turn-on methods (DC-Offset Sensing or Signal Sensing) and provides a positive 12V turn-on output to activate aftermarket amplifiers or other downstream electronics.
The LoC-22 includes the following features:
- Fully active, all analog circuit design by Bruce Macmillan, handles powerful factory amplifier outputs, up to 40 volts per channel
- Differential-balanced input architecture offers noise rejection and compatibility with most analog outputs from OEM source units and amplifiers
- Dual range input load switch (20 kΩ/Normal, 20 Ω/Low Z, thermally protected) for maximum compatibility with OEM amplifiers
- One stereo pair of crystal-clear, line-level RCA output jacks (up to 8V RMS)
- Automatic turn-on via DC-Offset or Signal-Sensing
- A dedicated 12V remote turn-on output (maximum 100 mA) to activate aftermarket signal processors or amplifiers
- Onboard LED clipping indicator makes output level setting quick & easy
- Ultra-compact chassis design fits into just about any installation location!
SKU: JL Audio - LoC-22 - Remote Level Control
JL Audio – M-DRC-50 Digital Preset Controller for JLid compatible products
Digital Preset Controller for JLid compatible products
The M-DRC-50 is a panel-mount, wired digital preset controller designed to connect to the JLid port of compatible JL Audio electronics.
Features:
- Provides easy, push-button selection of stored DSP presets for compatible JL Audio electronics
- Built-in RGB LED indicator displays selected preset by color
- Weatherproof construction (IP66 rated, from the front, when properly installed)
- One-hole mount design accommodates panels up to 3/4″ (19 mm) thick
- 18 ft. (5.5 m) control cable included, with protective connection sleeve
- Powered via the JLid connection; separate power wiring is not needed.
The M-DRC-50 is compatible with the following JL Audio products:
MVi-HUB: Connects to the JLid COMM Port
MVi Amplifiers*: Connects to the JLid COMM Port
*Not compatible with mono MV amplifiers.SKU: JL Audio - M-DRC-50 - Rear covers for Speakers
JL Audio – M-LCA-C-W Enclosed Speaker System Light Caps for 7.7-inch ETXv3 and 6.5-inch VeX models, Pair
Rear covers for SpeakersJL Audio – M-LCA-C-W Enclosed Speaker System Light Caps for 7.7-inch ETXv3 and 6.5-inch VeX models, Pair
Machined aluminum rear covers with LED down light for 7.7-inch ETXv3 and 6.5-inch VeX enclosed speakers
Take your ETXv3 and VeX speaker systems to the next level with these light caps.
Purpose-built for 7.7-inch ETXv3 and VeX enclosures, each cap features machined aluminum construction and a built-in, down-firing LED strip to illuminate the area below with brilliant white light. Installation requires just a single hole to be drilled. For retrofitting, each light cap can mount over an enclosure’s existing rear logo cap.
Note: Independent light cap functionality is not compatible with M3 or M6 ETXv3 and VEX systems equipped with RGB LED lighting.
Sold as a pair. Adds 0.655″ of thickness to the rear of each enclosure.
SKU: JL Audio - M-LCA-C-W - Rear covers for Speakers
JL Audio – M-LCB-C-W Enclosed Speaker System Light Caps for 8.8-inch ETXv3 models, Pair
Rear covers for SpeakersJL Audio – M-LCB-C-W Enclosed Speaker System Light Caps for 8.8-inch ETXv3 models, Pair
Machined aluminum rear cover with LED down light for 8.8-inch ETXv3 enclosed speaker systems
Take your ETXv3 speaker systems to the next level with these light caps.
Purpose-built for 8.8-inch ETXv3 enclosures, each cap features machined aluminum construction and a built-in, down-firing LED strip to illuminate the area below with brilliant white light. Installation requires just a single hole to be drilled. For retrofitting, each light cap can mount over an enclosure’s existing rear logo cap.
Note: Independent light cap functionality is not compatible with M3 or M6 ETXv3 systems equipped with RGB LED lighting.
Sold as a pair. Adds 0.741″ of thickness to the rear of each enclosure.
SKU: JL Audio - M-LCB-C-W
